E8000 adhesive is a fast-drying formula. To speed up the process, it’s better to apply some tricks while using the glue.
Once you apply the adhesive, you must increase the heat around the area. Moreover, the area should be well-ventilated, or external air should be applied using a fan.
Besides, increasing heat using a hairdryer or an electric blanket is also a good technique to make the glue faster.
There are a lot more tips and tricks that you need to know for a better drying experience.
Article Highlights
- For large areas, drying the glue in the sun is recommended.
- For small areas, using a hairdryer is recommended, especially for difficult areas.
- For hot glue, using compressed air is better.
- For superglue, applying an accelerator product is recommended.
Key Points of E6000
- Fast-drying formula
- Has exceptional strength with flexibility, durability, and strength
- Dries transparent, paintable, waterproof
- Viscosity is from low to medium
- Can be used for crafts, jewelry, woodworking, leatherworking, and other repairs
- Non-flammable, photo-safe, and washer/dryer-safe
- Withstands temperatures from -40 to 180 °F (10 to 32 °C)
- Indoor/outdoor-friendly
Ways To Make E6000 Glue Faster
E6000 is itself a fast-drying adhesive. But if you want your project to finish faster, you must be clever and take additional steps.
Increase Airflow
To make the glue dry faster, the first thing that comes to mind is increasing the airflow, especially on the surface. That’s precisely what you should do.
You can use a fan to do the process. It easily circulates air around the glue, helping to evaporate moisture. It’s also best for small and critical areas where air is tough to reach.
You can also use paper or any flat material to fan on the glued area, which removes the glue’s moisture and makes it dry.
Leave The Project In The Sun
Drying in the sun is the easiest method. Simply place the project in the sun and leave it to dry for some time.
It’s also a great solution for drying large areas. Select a sunny spot and leave the project for some time until it dries.
Use a well-ventilated area or an open space, and leave it under the sun for a faster experience.
Provide Additional Heat
Using additional heat means using a hairdryer, electric heater, or blanket.
When using a hairdryer, apply heat on a low setting. But make sure to avoid overheating the area, as this will burn the glue.
You must also apply the hairdryer 30 cm away from the glued surface, directly pointing at it.
Another way is to use an electric blanket. To do this, you need only switch on the blanket, make it warm, and place the glued surface on top of it.
If possible, cover the project with the blanket and leave it for some time. This will dry the glue faster.
If an electric heater is nearby, use it to create additional heat around the project. A heater is more helpful than a fan in winter or cold weather.
It’s also a great way to instantly dry the glue if drying in the sun takes too long.
To use it, turn on the heater and wait for it to warm the area. Then, shut the doors or windows and let it dry.
Apply An Accelerator
For super glue, it’s best to apply an accelerator product.
Super glues are formulated to dry faster. To speed up their drying time, use an accelerator spray.
Hold the spray 30 cm away from the surface where super glue is applied. You need to make sure the spray application is evenly coated.
Then, leave it for some time, and you will see that the glue has dried adequately within a few minutes.
Compressed Air for Hot Glue
For hot glue, using compressed air is recommended. It generally comes in a spray can.
You need to open the can of compressed air upside down, then spray it all over the area where hot glue is being applied.
Leave it for a few seconds to dry, and it’s done. However, you should be careful when using it as it can burn the skin if any contact happens.
Work In A Warm Environment
One simple way is to work in a warm environment. But the humidity should be low.
Any glue dries fast in warm weather. It helps to minimize moisture and make it dry.
The simple process is to choose a day and make the room warm.
A sunny day with low humidity is recommended because higher humidity and a cooler temperature will slow down the drying time, causing your work to be less than you wanted.
Make The Surface Dry
Applying correctly and following the rules helps to dry the glue faster with a smoother finish.
The most important thing is to make the surface clean and dry. It helps to stick even better.
To do it, dust off or wipe the surface with a cloth to remove excess water.
You can also use a damp cloth, let it dry, and then apply the glue. This will make the glue dry faster and stick better.
Also, use a well-ventilated area for a better finish and quicker experience.
Key Points To Remember
E6000 is itself a quick-setting glue. Follow these tips to maximize the drying time and complete the project as quickly as possible.
One of the main factors you must follow is providing heat with low humidity. By eliminating moisture, glues become dry faster at higher temperatures.
You can use a hairdryer, a fan, an electric blanket, or other similar items to do that.
You also need to ensure that the adhesive is applied thin enough for a speedy cure.
In addition, air circulation is essential. A fan would be a better choice for it.
Check for proper ventilation, temperature, and an evenly thin coat, and provide the proper time to dry.
Editor’s Note
E8000 adhesive is a quick-drying adhesive. It doesn’t need much time to dry, so it’s a better choice if you want rapid action.
But if you want a faster-setting experience, follow the instructions and apply the tricks accordingly.
Heat application and air circulation are the best and most useful ones.
If you learn the tricks and apply them properly, you will have a quicker experience and be able to eliminate the project in no time.